Start with the working solution, not the bottle
TETENAL Variobrom WA is a warm-tone black-and-white paper developer supplied as a 1L concentrate. The dilution you choose depends on how you process: 1 + 9 for dish or tray work, and 1 + 7 for machine processing. Those are different working solutions, so decide your method before you pour.
The developer suits both fibre-based and RC coated papers. On silver bromide papers it produces neutral to warm black image tones; on silver chloride papers the tones run warm black. That difference comes from the paper, not from changing the developer dilution, so pick your paper first and then mix the solution that matches your tray or machine.
What the Variobrom WA record confirms
- TETENAL Variobrom WA B&W Paper Developer 1L: Dish processing dilution: 1 + 9. This is the working strength for tray development, so mix to this ratio rather than guessing a tray dilution.

TETENAL Variobrom WA B&W Paper Developer 1L - TETENAL Variobrom WA B&W Paper Developer 1L: Machine processing dilution: 1 + 7. Machine processing uses a stronger working solution; do not use the tray dilution in a machine.
- TETENAL Variobrom WA B&W Paper Developer 1L: Development time at 20°C: RC coated papers 60–90 s; fibre based papers 90–120 s. Gives you a starting time window for tray work at 20°C, with RC papers developing faster than fibre.
- TETENAL Variobrom WA B&W Paper Developer 1L: Development time at 30°C: RC coated papers 30 s; fibre based papers 45 s. Shows how much the time shortens at a higher temperature, so you can adjust if your working solution is warmer.
A tray routine for warm-tone prints
- Mix the tray working solution at 1 + 9: Use the dish dilution for tray processing. The concentrate is high-yielding; the 1L bottle develops up to 50 m² of paper, so measure carefully rather than mixing by eye.
- Set your temperature and pick the time window: At 20°C, start RC papers at 60–90 s and fibre papers at 90–120 s. At 30°C, the record gives 30 s for RC and 45 s for fibre. Keep the whole tray set at a consistent temperature so the time window means something.
- Use a stop bath between development and fixing: The product record requires a stop bath after development and before fixing, for example Tetenal Indicet. Do not carry developer straight into the fixer.
- Track your throughput against the replacement rate: The record gives a replenishment rate of 350 ml/m². Note how much paper you put through a working solution so you can judge when to replenish rather than waiting for the print to look tired.
Why warm tone depends on the paper as much as the developer
Variobrom WA is described as producing neutral to warm black tones with silver bromide papers and warm black tones with silver chloride papers. If you want a pronounced warm tone, the paper choice is doing much of the work. The developer supports that look and gives deep blacks with very low stain, but it does not turn a neutral paper into a warm-tone paper.
That matters when you are buying paper for a project. Choose the paper first, then use Variobrom WA to develop it consistently. The 1L concentrate developing up to 50 m² means one bottle covers a long run of test strips and finished prints, which is useful when you are comparing papers.
Tray versus machine: what changes
The two processing methods differ in dilution and in how much attention you give the print. The record confirms both are supported; it does not supply machine settings beyond the 1 + 7 dilution.
- Tray processing: Mix 1 + 9. Development times at 20°C are 60–90 s for RC and 90–120 s for fibre; at 30°C they are 30 s for RC and 45 s for fibre. You control agitation and timing by hand.
- Machine processing: Mix 1 + 7. The record does not give machine development times or machine-specific operating steps, so treat the dilution as the confirmed starting point and follow your machine's own documentation for the rest.
Capacity and replenishment at a glance
- TETENAL Variobrom WA B&W Paper Developer 1L: This 1L bottle of concentrate will develop up to 50 m². Gives you a realistic sense of how far one bottle goes across a project or a season of printing.
- TETENAL Variobrom WA B&W Paper Developer 1L: Replenishment rate: 350 ml/m². Lets you plan replenishment by the area of paper processed instead of guessing from print appearance.
- TETENAL Variobrom WA B&W Paper Developer 1L: The developer is described as high-yielding and extremely stable. Supports using a single working solution across a longer printing session, though you should still track throughput against the stated rate.
What to confirm before you commit to a workflow
The supplied record covers dilution, development times at two temperatures, the stop bath requirement, capacity and replenishment. It does not include storage guidance for the concentrate or working solution, shelf life after opening, or agitation instructions. Those are not confirmed by the supplied information, so check the bottle label or the manufacturer's documentation before relying on a particular storage or agitation routine.
For a first session, keep the variables small: one paper type, one temperature and the tray dilution of 1 + 9. Use the time window for that paper and temperature, stop the development fully, and note the area of paper you process so the 350 ml/m² replenishment figure has something to attach to. Once the prints are consistent, change one thing at a time.


